If you say that the most "hot" furniture in the fall, you will definitely think of wooden furniture. That's right, because of the special nature of the material, solid wood furniture and flooring become high-risk objects in the autumn when the wind is high. Therefore, the fire prevention and maintenance tips of wooden floors and solid wood furniture must not be taken lightly.
NO.1: Analysis of the reason for the increase in floor gaps After the fall, the weather becomes dry, the humidity in the air is greatly reduced, and the solid wood floor will shrink, resulting in a large gap in the floor. There is some truth to the practice of delaying the maintenance of the company in the spring of the year. In the winter, the shrinkage of solid wood flooring is likely to increase.
Solution Fall repairs should be taken care not to worry, wait until the spring of the next year, after four seasons of warm and cold temperature changes significantly, solid wood floor cracking and deformation problems no longer develop, and then a one-time repair. This will ensure better results and eliminate the hassle of repeated repairs.
special reminder:
Autumn is coming, solid wood floor waxing maintenance is at the time. Wipe the floor clean before waxing, then apply a layer of floor wax evenly on the surface. After a while, wipe it with a soft cloth until it is smooth and bright. Ventilation should be done as much as possible to keep the air flowing inside the house. After a while, after the weather is getting dry, you need to use a humidifier to adjust the indoor humidity.
Moderate hydration, prevent cracking wet rags, wipe the wet cloth, and twist it until it does not drip. Or use a small humidifier to moisturize the room, drop two or three drops of aroma, not only can play the role of floor moisturizing, but also create a warm and comfortable home environment.
Avoid exposure, properly cover the location of long-term exposure to home, such as balconies, floor-to-ceiling windows, etc., you can consider laying carpets on the floor or placing floor vases to protect the floor from direct sunlight.
Pay attention to cleaning. Regular dust removal should pay special attention to the position where it is often stepped on. It is appropriate to lay carpet and dust-proof strip on the floor of the doorway. At the same time, the wood floor is regularly waxed or oiled to maintain its service life.
Keep away from the heat source, be careful to deform the autumn weather to get cold. Some families will put some heating appliances such as heating blankets directly on the floor. This may cause the floor to be unevenly deformed by heat. Thick carpets should be placed on the floor before using heat sources.
NO.2: The reason for the loss of luster of solid wood furniture is that the surface of solid wood furniture is coated with paint, which is especially important for the maintenance and maintenance of the paint film. Once the paint film is destroyed, it not only affects the appearance of the surface, but also further affects the internal structure of the product. Poor maintenance in autumn can lead to tarnishing or cracking of solid wood furniture.
The solution should always keep the solid wood furniture clean. Use a pure cotton soft cloth to wipe off the surface dust every day, and wipe it with a damp cloth for two or three days. If there are stains on the surface of solid wood furniture, do not rub it hard. Use warm tea to remove the stains gently.
special reminder:
In fact, it is advisable to use thin glue to separate the solid wood furniture from the ground, and at the same time let the wall of the solid wood furniture maintain a gap of 0.5-1 cm from the wall. Avoid too humid environments to avoid rotting solid wood furniture.
A good way to avoid chemical solvents in addition to stains on the surface of solid wood furniture, if there are stains, do not rub hard, this will break the protective paint on the surface of the ring, which will make the solid wood furniture tarnish. Therefore, the stain can be gently removed with warm tea water.
When avoiding scratches on hard objects, do not touch the cleaning tools to solid wood furniture. Always pay attention to the hard metal products or other sharp objects that collide with the furniture to protect the surface from scratches.
Avoid contact with heat source. It is best to place the solid wood furniture at a distance of about 1M from the heating flow to avoid high-temperature baking for a long time, causing local cracking, deformation and local deterioration of the paint film.
Avoid using oily cleaners. It is best to place solid wood furniture at a distance of about 1M from the heating flow to avoid high-temperature baking for a long time, causing local cracking, deformation and local deterioration of the paint film.
NO.3: The reason why the door frame is cracked is that unless it is a good quality and very thick wood line, it is not solid to install the door cover directly with thin wood lines because the physical properties of the material are different. The door cover is not easily in stable contact with the wall. In addition, the wood line with insufficient thickness will crack and deform when it comes into contact with the wall.
Solution The adhesive can be used to fill the cracks in the door cover and then repaired with the original color paint of the door cover. If the door cover material is too thin, it is best to ask the worker to rework.
special reminder:
Autumn is coming, solid wood floor waxing maintenance is at the time. Wipe the floor clean before waxing, then apply a layer of floor wax evenly on the surface. After a while, wipe it with a soft cloth until it is smooth and bright. Ventilation should be done as much as possible to keep the air flowing inside the house.
NO.4: Analysis of the cause of the breakage of the seamless tile due to the difference between the thermal expansion and contraction coefficient of the base layer, the bonding layer and the tile itself. Under the thermal cold tension damage of 1~2 years, the overly dense tile is easy to cause the tile. Problems such as swelling and breaking. If you re-mass a large-scale paving after such problems, the cost will be two or three times more expensive than the first time.
Solution Remove the sand from the back of the tile and mix it with cement and glue. It should be noted that if the tile is only partially peeled off, it is not possible to tap the mortar on the base layer to prevent the original tile from being loose.
special reminder:
The seam can be adjusted between 2 and 3 mm. At the same time, in order to avoid wasting materials, a number of selected products can be randomly sampled on the ground for non-bonded test shops. If there are obvious chromatic aberrations, dimensional deviations, etc., if the satisfactory results are not achieved after the adjustment of the brick position, the laying should be stopped in time, and contact with the material supplier for replacement. NO.5: Analysis of the reasons for the corners of the wallpaper. To "water" the wallpaper, let the wallpaper be dry and dry, but not the ventilation in the summer. Because it is so easy to let the freshly laid wallpaper be blown dry by the wind, thus losing water and deformation.
Solution Clean the original glue on the wallpaper, brush some white latex on the back of the wallpaper, brush the water on the front of the wallpaper, and scrape it with a plastic scraper. Finally, the bead is attached, and the bead is removed after the drying. Because the autumn climate is relatively dry, the wallpaper and wall coverings must be soaked in the water before the paving, and then the glue is applied.
special reminder:
If you encounter wallpaper blistering, first use the sewing needle at home to smear the bubbles on the surface of the wallpaper, release the gas, then use the needle to draw the appropriate amount of adhesive, inject into the needle that has just been punctured, and finally scrape with a squeegee. Compact and dry. >>>I come to pick up a good method NO.6: Analysis of the danger of explosion in the shower room The inside of the glass shower room is a closed space. When the high temperature and high pressure accumulate to a certain extent, it will form pressure on the glass, resulting in uneven heating of the glass. explosion.
Solution The glass is coated with a high-quality transparent safety explosion-proof membrane, which can increase the strength of the glass by more than 6 times. Even if it bursts, the self-explosive glass fragments can be adhered together by the adhesive force of the explosion-proof membrane to prevent the glass from being self-explosive. The shards of glass splatter hurt people.
special reminder:
Although the strength of tempered glass is relatively high, the characteristic of tempered glass is that it is more afraid of sharp things than ordinary glass. The fixed shower room and the positive end of the wall will affect the safety of tempered glass. If it is collided again, it will easily cause the whole. explosion.
Coated Denim refers to a product that is uniformly coated on the surface of a Denim to form a film of a polymer compound, which changes the appearance, style, or functionality of the fabric, thereby increasing the added value of the product.
In accordance with its special features classification, style coating, such as pan-old, film sense, wax sense, paper sense, etc .; special functional coating such as water pressure, waterproof moisture, anti-ultraviolet, flame retardant and so on.
Denim fabric transparent plastic coating, color plastic coating and gold, silver powder coating special effects, with a different washing process such as: general wash, rinse, yeast and yeast, etc., finishing the denim color rich, become Home textiles and clothing industry fashion preferred fabric, while inspiring denim clothing designer's creative inspiration.
Coated Denim
Coated Denim,Coated Denim Fabric,Grey Coated Denim,Black Coated Denim
Dongguan Zhongtang yu' an Weaving factory , https://www.yuanfabric.com